Amiga 600 FPGA (MiSTer) Conversion

[ubermick]

Wow. It appears I’ve found my next project.

That said, anyone find a different keyboard interface than the Tynemouth? Appears the coronavirus shut them down...

(Edit... oop, looks like the Keyrah is the way to go?)

[chandkumar3g]

That is really impressive!

[obitus1990]

Matt,

Do you have any plans to complete the A1200 3D print frame for the MiSTer that you've posted on Thingiverse? I see it's been 6 months since your last login here...so hopefully you'll see this in the near future.

Thanks!

[astuermer]

1x DC Power Supply Jack Socket Female Panel Mount Connector 5.5 x 2.1mm, Fitting hole of 7.8mm with rear locking nut.
https://www.mouser.at/ProductDetail/502-PC722A - Is this correct?

1x Mini Panel Mount Switch 3A 250V ON-OFF SPST Dimensions 15x10x17mm Mounting Hole 14x9mm.
(???)

1x 8mm Mini Waterproof Car Momentary Push Button Switch Zinc-Aluminium *This one differs to Matt's.
(???)

1x Adafruit Panel mount HDMI Cable 40cm part number ADA978, *This is a perfect fit.
https://www.mouser.at/ProductDetail/485-978

2x SparkFun USB Type A Female Breakout part number BOB-12700
https://www.mouser.at/ProductDetail/474-BOB-12700

1x Micro SD TO Micro SD Card Extension Cable Adaptor Extender
https://www.mouser.at/ProductDetail/485-3688

1x Heatsink with 3m tape for DE10 FPGA Dimensions 22x22x10mm
https://misterfpga.co.uk/product/mister ... o-cooling/

1x Adafruit ZERO4U 4-PORT USB HUB without POGO pins v1.3 part number ADA4115
https://www.mouser.at/ProductDetail/485-4115

1x Micro USB B Male to Mini USB B Male Data Cables Digital Cables Cord OTG Adapter
(???)

Uh that's an impressive list...

From the photos of the finished project I am missing those USB cables from the hub to the two ports on the right side of the Amiga including the pins to mount them on the BOB-12700 boards...

• Internal USB cables to BOB-12700 board(s) - https://www.mouser.at/ProductDetail/971-4D-PROGM-CABLE
• Pin connectors for USB cables - (???)

And does anyone know where to get the Amiga keyboard to USB adaptor?

Regarding those MiSTer parts, I can recommend misterfpga.co.uk... bought my USB hub and RTC board there...

• USB Hub v2.1 For MiSTer > https://misterfpga.co.uk/product/usb-hu ... ster-fpga/
• MiSTer IO Board v6.1 with Fan - https://misterfpga.co.uk/product/mister ... -with-fan/
• MiSTer SDRAM XS v2.2 32MB Memory Addon Board - https://misterfpga.co.uk/product/mister ... don-board/
• MiSTer RTC Real Time Clock Board v1.3 - https://misterfpga.co.uk/product/mister ... -rtc-v1-3/

Regarding a basic MiSTer set I can recommend MiSTer-FPGA.de https://www.mister-fpga.de/

I am planning to do this build too - got the A600, got the MiSTer - but missing all those small parts.
I could find all of them so far... those I've found I added up there.

Does anyone who built this thing have a precise list with perhaps model/part numbers?

Kind regards, Andi

[Jimiga]

Thanks for sharing your creation, really impressive and got me thinking.

I have a MiSTer and would love to build it into a compact system like this. Also just acquired an A600 case and keyboard!

I see there's a little soldering and such involved, I'd be new to that and wondered if this could be tackled by a beginner? Do you happen to have a little breakdown of what required soldering and how you achieved that?

Your input would be very helpful, thanks again for sharing and I hope you're still enjoying this modern take on the Amiga experience!